# SITE ENGINEER GRADE II,FILM DEVELOPMENT CORPORATION SOLVED PAPER 2015

SITE ENGINEER GRADE II,FILM DEVELOPMENT CORPORATION
EXAM DATE:06-10-2015

1.Any trap should have:
A.Water seal*
B.Sullage
C.A bend
D.Grating
Ans:A

2.Eco system is:
A.Hatbitat
B.Communit=y and environment*
C.Community
D.Biosphere and habitat
Ans:B
3.The outer signal is provided at a minimum distance of:
A.1 km from home signal
B.580 m from home signal*
C.860 m from home signal
D.180 m from home signal
Ans:B
4.A thin cylinder of diameter 100 m and thickness 5 mm is subjected to a internal fluid subjected to a internal fluid pressure of 10N/mm2.The hoop stress is:
A.150 N/mm2
B.10 N/mm2
C.15 N/mm2
D.100 N/mm2 *
Ans:D
5.In a theodolite traversing the angular error should not exceed using 20” least count theodolite and ‘n’ number of sides:
A.20”Square root of  n*
B.20”xN2
C20”xSquare root of n2
D.20”x2n
Ans:A
6.A horizontal force 40 kgf is applied on a body of weight 120 kg placed in a horizontal plane.If the body is just in the point of motion,the angle of friction be:
A.200
B.180 26*
C.100
D.250
Ans:B
7.An equation for a deficient frame:
A.n=2j+3
B.n=2j-3*
C.n=j+3
D.n=j-3
Ans:B
8.The process of applying cement mortar under pressure through a nozzle is called:
A.Pressurising
B.Prestressing
C.Guniting*
D.Compressing
Ans:C
9.An example of endogenous tree is:
A.Bamboo*
B.Teak
C.Deodar
D.Oak
Ans:A
10.The purpose of soundness list is to determine:
A.The presence of free lime*
B.Setting time
C.Sound proof quality of cement
D.The fineness
Ans:A
11.The maximum permissible excentricity of load on a rectangular foundation with width B is equal to:
A.B/3
B.B/6
C.B/2
D.B/4*
Ans:D
12.The portion of the brick obtained by cutting into two portion longitudinally is called:
A.Bat
B.King closer
C.Queen closer*
D.Beveled closer
Ans:C
13.The inner curve of an arch is:
A.Spandril
C.Soffit
Ans:B
14.Life became essential in a building when the number of floors exceeds:
A.2
B.3
C.4*
D.6
Ans:C
15.The moment of inertia of a rectangular section having b-width and d-depth about x-axis is given by:
Ans.bd3/12
16.The ratio of volume of voids to the total volume of given soil is:
A.Voids ratio
B.Porosity*
C.Air volume
D.Air area
Ans:B
17.A pull of 20 t is suddenly applied to a road of cross-sectional area 40 cm2.The stress produced in the rod is equal to:
A.0.5 t/cm2
B.1.0 t/cm2
C.2.0 t/cm2 *
D.4 t/cm2
Ans:C
18.In a fixed beam,the slopes at the ends are:
A.Minimum
B.Maximum
C.Same as at centre
D.Zero*
Ans:D
19.Adesirable pH value for water is:
A.7
B.6 to 8
C.5 to 9
D.7 to 8.5*
Ans:D
20.The magnetic bearing of a line AB is 212030 and the declination 2015’ east.What is true bearing of the line?
A.210015’
B.214045’*
C.210045’
D.132030
Ans:B
21.The process of proper and accurate measurement of concrete ingredients for uniformity proportion is known as:
A.Batching*
C.Mixing
D.Blending
Ans:A
22.The distance to the neutral axis from the top compression fibre of a singly reinforced rectangular beam is:
Ans:Xu=(0.87 fy Ast)/0.36 fck b
23.The bearing stiffeners in plate girders are provided at:
A.Mid span
B.Quarter points
C.Supports*
D.Equal intervals
Ans:C
24.The most economical section
A.Square
B.Circular
C.Channel
D.Tubular*
Ans:D
25.Bearing of OA=23030’ and bearing of OB=120000’,DAOB is:
A.99030’*
B.100030’
C.140030’
D.280000’
Ans:A
26.The value of dismantled material less the cost of dismantling is called:
A.Scrap value*
B.Salvage value
C.Book value
D.Marhit value
Ans:A
27.Back washing is highly effective in case of:
A.Slow Sand filters
B.Rapid sand filters*
C.Pressure filters
D.Rapid and slow sand filters
Ans:B
28.Colour of fresh sewage:
A.Brown
B.Gray*
C.Pink
D.Black
Ans:B
29.If’W’is the weight per volume,’P’safe bearing capacity and  is the angle of repose of soil retained by the retaining wall.The minimum depth of foundation is:
Ans:
30.The bending moment in a beam will be maximum where:
A.The shear force is uniform
B.The shear force is maximum
C.The shear force is zero*
D.The shear force is minimum
Ans:C
31.A steel wire of 5 mm diameter is bend into a circular shape of 5 m radius.Young’s modulus E=200 GPa.The maximum stress induced in the wire is:
A.100 N/mm2 *
B.100 N/mm2
C.10 N/mm2
D.1 N/mm2
Ans:A
32.A unit is working in anaerobic action is:
A.Activated sludge process
B.Tricling filter
C.Contact bed
D.Septic tank*
Ans:D
33.The primary function of sleeper is:
A.To maintain gauge*
B.To take loads from rails
C.To give cushioning action
D.To give stability of the train
Ans:A
34.ABCD is a square.The bearing of AB is 500.the bearing  of DC is:
A.1400
B.1900
C.500 *
D.2900
Ans:C
35.The sum of Interior angles of a closed traverse is:
A.(2n-4)90*
B.(2n+4)90
C.(2n-4)180
D.(2n+4)180
Ans:A
36.Current meter is used for measuring:
A.Velocity*
B.Viscosity
C.Current
D.Pressure
Ans:A
37.The quantity of cement required for the ratio of 1:5 in cement mortar is:
A.288 kg*
B.240 kg
C.178 kg
D.206 kg
Ans:A
38.In a problem the algebraic sum of all horizontal (aH)is 16 N and the algebraic sum of all vertical force(aV)is 32 N.The resultant force is:
A.48.5 N
B.35.8 N*
C.38.5 N
D.40 N
Ans:B
39.The process of adding water to lime and convert it into hydrated lime is called:
A.Watering
B.Baking
C.Hydration
D.Slaking*
Ans:D
40.Francis turbine is:
A.Impulse turbine
B.Radial flow impulse turbine
C.Axial flow turbine
D.Reaction radial flow turbine*
Ans:D
41.A curve consists of two arcs of equal or different radii bending in opposite direction is:
A.Simple curve
B.Compound curve
C.Reverse curve*
D.Transition curve
Ans:C
42.The latitude and departure of any point with reference to the preceding point is known as:
A.Independent co-ordinate
B.Consecutive co-ordinate*
C.Total latitude
D.Total departure
Ans:B
43.Bemoullis theorem deals with the law of conservation of:
A.Mass
B.Momentum
C.Energy*
D.Velocity
Ans:C
44.For a simply supported beam,the maximum deflection permitted is:
A.1/300 of the span
B.1/325 of the span*
C.1/350 of the span
D.1/400 of the span
Ans:B
45.In a cantilever retaining wall for height’H’,the horizontal pressure of the earth will act at a distance of:
A.H/3 from the top
B.H/3 from the base*
C.H/2 from the top
D.H/4 from the base
Ans:B
46.Core-cutter method is used for:
A.Determining density of soil*
B.Obtaining samples for direct shear test
C.Determining bearing capacity of soil
D.Compacting soil
Ans:A
47.The indentation provided in a face of the brick is called:
A.Plank
B.Pallet
C.Striker
D.Frog*
Ans:D
48.Inlimit state method of design,the over reinforced sections:
A.Are not permitted*
B.Are permitted
C.Are permitted only in extreme fibres
D.Permitted in any case
Ans:A
49.Polar moment of inertia of a solid shaft of diameter D is:
Ans:(Pie/32)*D4
50.A chain 20 m long is 20 cm too short was used to measure a line and the result was 190 m.The true length is:
A.188.1 m*
B.191.5 m
C.193 m
D.190 m
Ans:A
51.Combined correction for refraction and curvature of 1 km is:
A.0.0112 m
B.0.0673 m*
C.0.0785 m
D.0.0073 km
Ans:B
52.A 15 cm theodolite means:
A.Length of the telescope is 15 cm
B.Height of standards is 15 cm
C.Diameter of lower plate is 15 cm*
D.Radius of upper plate is 15 cm
Ans:C
53.CPM stands for:
A.Computer Programming Mode
B.Critical Project Management
C.Critical Path Method*
D.Controlling,Planning and Maintenance
Ans:C
54.The approximate weight of 1m3 of mild steel is:
A.1000 kg
B.240 kg
C.14000 kg
D.7850 kg*
Ans:D
55.In a closed travers the algebraic sum of deflection angle is:
A.00
B.3600 *
C.(2n+4)*9
D.(n-2)180
Ans:B
56.For a level section area of a  trapezoidal cut when base width ‘B’ side slope ‘S’ and depth’d’:
A.Bd+Sd2 *
B.Bd2+Sd
C.Bd-Sd2
D.Bd2-Sd
Ans:A
57.In a riveted joint,when the number of rivets decreses from the innermost to the outermost row the joint is said to be:
A.Chain
B.Zig-Zag riveted
C.Diamond riveted*
D.Single riveted
Ans:C
58.The best type of ballast is :
A. granite
B.Sandstone
C.Limestone
D.Quartzite*
Ans:D
59.A small reflecting instrument is used to fixing up intermediate points on the line is called:
A.Line ranger*
C.Open cross staff
D.Offset rod
Ans:A
60.Hydraulic ram is a pump which works:
A.On the principle of water hammer
B.On the principle of centrifugal action
C.Principle of reciprocating action*
D.Direct action
Ans:C
61.When water table is within the root zone depth and is determined to the plant life,the land is said to be:
A.Basin flooding
B.Water logged*
C.Over nourished
D.Super saturated
Ans:B
62.The best pipe for water mains for long life is:
A.Steel
B.Cement concrete
C.Cast iron*
D.Asbestos cement
Ans:C
63.The best system of a railway highway crossing is:
A.Level crossing
B.Road over rail track*
C.Road under rail track
D.Both road over and under bridges
Ans:B
64.The process of taking out stones from natural rock is:
A.Dressing
B.Seasoning
C.Quarrying*
D.Pitching
Ans:C
65.If the higher values are outside ,series of closed contours on a plane indicate a:
A.Hill
B.Depression*
C.Valley
D.Ridge
Ans:B
66.The surface of a still lake is an example of:
A.Horizontal surface
B.Datum surface
C.Level surface*
D.Horizontal plane
Ans:C
67.Two forces P and Q are acting at an angle q,their resultant R is given by:
Ans:R=Square root of P2+Q2+2PQ cos(theta)
68.The road connecting district headquarters of a state is:
A.State Highway*
B.National Highway
Ans:A
69.Pile foundations are normally used:
A.In soft clayey soils
B.In heavy load situations
C.When the bearing area required is not available*
D.In loose sandy soil
Ans:C
70.A simply supported beam of span’I’carries a point load ‘w’ at its centre and rigidity  of beam is ‘El’.The maximum deflection at the centre is:
Ans:wl3/48El
71.The Headquarters of FIFA is located at--------
A.New York
B.Munich
C.Zurich*
D.London
Ans:C
72.Conaru Hampi’s name is associated with-----
A.Chess*
C.Snooker
D.Tennis
Ans:A
73.The Chief Minister of Maharahtra is-----
A.Ashok Chavan
B.Deshmukh
D.Ajith Pawar
Ans:C
74.The 8th G-20 Summit held at -----------
A.New Delhi
B.Moscow*
C.Geneva
D.Sri Lanka
Ans:B
75.’Conversations with my life’ was written by--------
A.Man Mohan Singh
B.R.K.Narayan
C.P.V.Narasimha Rao
D.Nelson Mandela*
Ans:D
76.Poyikayil Yohannan’s name is associated with-----------
A.PRDS*
B.SYDD
C.Yogakshema Sabha
D.SNDP
Ans:A
77.The East flowing rivers of Kerala are the tributaries of River----------
A.Periyar
B.Bharathapuzha
C.Pampa
D.Kaveri*
Ans:D
78.The leader of ‘Malayalee Memorial’was-------
A.Dr.Palpu
B.G.P.Pillai*
C.N.Raman Pillai
D.R.Ranga Rao
Ans:B
79.Who among the following founded the organization ‘Samathwa Samajam’?
A.Vaikunda Swamikal*
C.Sree Narayana Guru
D.Kumaranasan
Ans:A
80.Yogakshema Prasthanam started in the year-----------
A.1906
B.1908*
C.1912
D.1914
Ans:B
81.Lucknow city is situated on the banks of the river---------
A.Gomati*
B.Yamuna
C.Ganga
Ans:A
82.Which district in Kerala has the largest forest area?
B.Idukki*
C.Malappuram
D.Kasarkodu
Ans:B
83.The first concrete dam in India is------
A.Bhakranangal
B.Hirakud
C.Mattupetti*
D.Malampuzha
Ans:C
84.Which temple is known as ‘Dakshina Kashi’?
A.Guruvayoor
B.Sabarimala
C.Vaikom Siva Temple*
Ans:C
85.Who among the following is known as’The father of Indian Renaissance’?
A.Bankim Chandra Chatterjee
B.Ram Mohan Roy*
C.Debendranath Tagore
D.Gopalakrishna Gokhale
Ans:B
86.SNDP was formed in the year-----------
A.1901
B.1903*
C.1905
D.1908
Ans:B
87.Who among the following was the first President of All India Trade Union Congress?
A.Tilak
B.Gokhale
C.Lala Lajpath Rai*
D.S.N.Banerjee
Ans:C
88.Communist Party of India was formed in the year---------
A.1920
B.1923
C.1925*
D.1927
Ans:C
89.’Kevala Devu National Park’ is situated at-----------
A.Rajasthan*
B.Uttarakhand
C.Punjab
Ans:A
90.Guruvayoor Sathyagraha was in the year-----------
A.1923
B.1924
C.1925
D.1931*
Ans:D
91.The standard dimension of brick as per Indian standard is:
A.20x10x10 cm
B.22.5x11.5x8 cm
C.19x9x9 cm*
D.18x9.5x9.5 cm
Ans:C
92.The aggregate is fine if it is completely retained on:
A.0.15 mm sieve*
B.0.30 mm sieve
C.4.75 mm sieve
D.1.18 mm sieve
Ans:A
93.One arc is:
A.1 m2
B.100 m2 *
C.1000 m2
D.10 m2
Ans:B
94.The WCB of a line OA is 1320 its guadrantal bearing is:
A.S 480E*
B.S 480W
C.N 3120W
D.E 480S
Ans:A
95.Chercy’s formula is given as:
Ans:V=C Square root of mi
96.The algebraic sum of the moments taken about any point in the plane of forces is zero is known as:
A.Law of polygon of forces
B.Lamis theorem
C.Newton’s law of force
D.Laws of moments*
Ans:D
97.The resultant hydrostatic force acts through a points is known as:
A.Centre of gravity
B.Centre of buoyancy*
C.Centre of pressure
D.Centroid
Ans:B
98.The centre of gravity of quadrant of circles is at a distance of:
Ans:4r/3(Pie) from the axis
99.If the Poisson’s ratio of a material is 0.25,the ratio of modulus of rigidity to the Young’s modulus is:
A.2
B.4
C.2.5
D.0.4*
Ans:D
100.The point of contraflexture is the point where:
A.Shear force is zero
B.The bending moment is Zero
C.Beam is supported
D.The bending changes its sign*
Ans:D

Please Give Us Your 1 Minute In Sharing This Post!
SOCIALIZE IT →
SHARE IT →